Hinweis: Diese Seite ist ausschließlich in englischer Sprache verfügbar.
Built-in FlashAll modern Minolta AF cameras have a built-in flash. It has the following characteristics:
- Its guide number is low, typically 12 meters. This is sufficient for fill flash and short distances.
- It always supports TTL-OTF metering (except for digital cameras).
- It does not support HSS or pre-flash metering (with film cameras).
- It does support ADI when the body supports it.
- It's used as an AF assist light when the camera doesn't have a dedicated AF illuminator.
- It's used as a controller for wireless flash when the body supports it.
Dedicated FlashA dedicated flash is mounted on the camera or attached to the camera by cables. The first series of Minolta AF cameras had the ISO flash shoe. Newer Minolta cameras and most Sony DSLR and SLT cameras have the newer iISO shoe. The latest Sony SLT and ILCE cameras have the Multi Interface shoe. You can mount old Minolta AF flashes on new cameras and vice versa using adapters, as well as flashes with the iISO shoe on Multi Interface cameras and vice versa.
Dedicated flashes typically have a higher guide number than built-in flashes, they carry extra batteries, have zooming reflectors and AF illuminators, can tilt and swivel and support additional flash metering modes like pre-flash metering and ADI. See the Flash table to see which Minolta/Sony flash supports which feature.
Wired FlashMinolta uses a wiring system with 4-wire cables. With this system you can build a TTL-capable wired remote flash system. Most flash functions are still available when using wired flash. The camera can shoot at shutter speeds up to the x-sync speed. Flash modes like ADI are not supported when the flash is off-camera.
The cabling system also allows to attach more than one flash to the camera, and all work in TTL mode.
With modern cameras you use the cable OC-1100/FA-CC1AM to attach the flash to the camera. The OS-1100/FA-CS1AM has an iISO flash foot at one end, the Minolta flash plug at the other end and a coiled 4-wire cable in between. This cable can be extended with the cable EX/FA-EC1AM, which consists of a flash plug, a flash socket and 1 meter of coiled cable. You can use several cables EX/FA-EC1AM to get a really long cable.
The OC-1100/FA-CC1AM cable plugs into a socket at the side of several flash units. Other flash units do not have this socket. For these, you need the OS-1100/FA-CS1AM flash shoe. You mount the flash on the OS-1100/FA-CS1AM like you would mount it on the camera. The OS-1100/FA-CS1AM provides the flash plug socket, a plastic ISO foot (without contacts) and 1/4" threads. The OS-1100/FA-CS1AM is also useful when you like to mount the flash on a bracket or tripod.
With new Multi-Interface cameras or flashes the cabling is slightly different. To attach a cable to the camera you use a Sony FA-CS1M. This connector does not have a cable attached, but has a Sony/Minolta 4-wire flash socket. So you need a Minolta CD/Sony FA-MC1AM cable to attach to the FA-CS1M. The other end of the cable either attaches directly to a flash with a built-in socket, or (for flashes without a socket) to another FA-CS1M (Multi-Interface shoe) or a OS-1100/FA-CS1AM (iISO shoe). To extend the cable you can use cables EX/FA-EC1AM as with an iISO system.
See the Flash Table to see which Minolta/Sony flash unit has a built-in socket.
Some camera bodies and some flashes support using the flash off-camera without cables. The flash is triggered by the camera body wirelessly. Most bodies use the built-in flash to control the remote flash, or a suitable dedicatated flash mounted on the camera. There is also a separate Minolta Wireless Flash Controller. It was primarily intended for the Dynax/Maxxum 9xi which was capable of wireless flash but did not have a built-in flash. The Minolta Wireless Flash Controller also works on many later bodies. However, it's discontinued, and some of the latest bodies no longer support it.
With this system, the built-in flash not only triggers the remote flash, but also can stop it. Minolta's wireless flash system therefore is capable of TTL flash metering. The remote flash is not triggered by a simple light pulse like slave flashes. Instead, the body uses a series of coded pulses to control the remote flash. These coded pulses are emitted by the built-in flash. They are weak in intensity, but depending on the lighting situation they may be visible in the picture. To avoid this the Minolta Wireless Flash Controller can be used (if supported by the body).
With wireless flash you can also trigger multiple remote flashes. All are started and stopped by the body, so the system still works in TTL mode.
Minolta's wireless flash system uses four channels, and a flash unit can listen on one of the four channels. The camera controls one channel, and all flashes assigned to that one channel are triggered. The body learns the channel by having the flash mounted on the body when switching to wireless flash. This allows to have more than one set of flashes in the same area, each controlled by a different camera. Some flashes support only two of the four channels.
Sony has introduced wireless flash control via a radio controller and receivers. It can control up to 15 flashes in up to 5 groups on 14 channels. Wireless TTL and wireless HSS are supported (TTL not with some flashes).
There are four generations of the wireless flash protocol. The characteristics are:
Generation 1: Analog wireless flash
- shutter speed limited to 1/60 or 1/45 (depending on camera)
- allows to balance the built-in flash and the remote flash with a 1:2 ratio, ie. the built-in flash contributes 1/3 of the light and the remote flash contributes 2/3 of the light
- supported by many film cameras, flashes and by Minolta Wireless Flash Controller
Generation 2: Wireless HSS and digital
- camera can use shutter speeds between 1/60 and x-sync
- camera can use shutter speeds shorter than x-sync (Wireless HSS)
- supported by DSLRs
- supported by some film cameras (used when shutter speed is shorter than 1/60)
- requires Minolta D flash or Sony flash
- no ratio flash with digital
- not supported by Minolta Wireless Flash Controller
Generation 3: Digital ratio flash
- ratio flash with DSLRs
- supported by later Sony cameras (see table below)
- requires Sony HVL-F60M, HVL-F58AM, HVL-F45RM, HVL-F43AM or HVL-F43M as controller on camera
- up to 3 flash groups when using only HVL-F42AM, HVL-F43AM, HVL-F43M, HVL-F45RM, HVL-F58AM and HVL-F60M as remote flashes (mode CTRL+/CTRL1)
- up to 2 flash groups when using mix of Minolta D flashes and Sony flashes as remote flashes (mode CTRL/CTRL2)
Generation 4: Wireless flash with radio controller
- ratio flash with some mirrorless cameras
- supported by later Sony ILCE/ILCA cameras (check table below)
- requires FA-WRC1M as controller on camera, or radio control capable flash
- requires remote flashes on FA-WRR1 as receiver, or radio controllable flash
- up to 5 flash groups
The following interactive table helps finding combinations of cameras and flashes for wireless flash. Select cameras and flashes from left to right, and the result will be the level of wireless flash support. If you can't make the desired selection at one point, the desired combination is not supported for wireless flash.
Note that some combinations of camera and controlling flash require a flash shoe adapter.
|Camera||Flash used as controller||Flash used as remote flash||Support|
© 2017 Michael Hohner; Diese Seite wurde zuletzt am 30.06.2017 geändert.